KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
HOCS AVANT
Kimpex
#
072915
a Wolverine 1995
INSTRUCTIONS D’ASSEMBLAGE
schéma D
schéma B
r l’installation d’un treuil sur le pare-chocs avant Kimpex, veuillez utiliser les trous de position arrière,
n utiliser les trous avant.
pare-chocs sous le tube inférieur du grillage.
(Voir schéma A)
inférieur du grillage, fixer à l’aide des brides en «U»
1-1/8” diam. X 4-5/8”
, des boulons hex.
2”
et des écrous autobloquants
5/16” nc
.
essous du pare-chocs à l’aide des deux supports , des brides en «U»
1” diam. X 4-1/4”
, des boulons
” nc X 2”
et des écrous autobloquants
5/16” nc
, au bas du cadre original.
(Voir schéma B)
supports
en dessous du pare-chocs
à l’aide des boulons hex.
5/16” nc X 3/4”
et des écrous
uants
5/16” nc
. Serrer le tout.
(Voir schéma C)
s capuchons de plastique aux deux extrémités du tube.
(Voir schéma D)
tion
N° d’article
Quantité
cs avant
81-828-1000
1
81-828-2000
2
ex. 5/16” nc X 3/4” S1711-00506-022 2
ex. 5/16” X 2”
S1711-00516-022 4
Réf. Description
N° d’article
Quantité
Écrou autobloquant 5/16” nc S4186-10500-022 6
Bride en «U» 1” diam. X 4-1/4” Q2116-20002
2
Bride en «U» 1” diam. X 4-5/8” Q2118-20001
2
Capuchon de plastique
S8111-00007-500 2
A-2810354
2810354
ATV
Mounting instructions
FRONT AND REAR A-ARM BRACKET KIT
Kimpex
# 375228
For "Commander Wide Track" and "Commander Trek" track kit Kymco 500
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
2810354
A-2810354
FRONT AND REAR A-ARM BRACKET KIT
Kimpex
#
375720
For “Commander Wide Track” and “Commander Trek” Track Kit
MOUNTING INSTRUCTIONS
5
FRONT A-ARM BRACKET INSTALLATION
(see sketch D)
WARNING :
Prior to installation, turn off the engine, put
in two-wheel driving mode and the transmission in
neutral, and block the wheels.
1)
Raise h front of the ATV off the ground and remov th
wheels.
WARNING :
When the ATV is raised, make sure t at it is
properly secured/supported to prevent it from
accidentally falling during the installation of the A-arm
brackets. If not properly se ured/supported, serious
physical injury could occur.
2)
R move the front left CV shield. Do not discard. They will be
reinstalled later.
3)
Insert the
1/2” nc X 2-1/2”
carriage bolt (#
10
) into the hole
intended in the front left A-arm bracket (#
5
).
4)
Install the front left A-arm bracket (#
5
) under the lower front
A-arm so that the two parts fit snugly.
5)
Install the front A-arm clamping plate (#
4
) above the lower front
A-arm and fasten it onto the A-arm bracket (#
5
) using
(4) 3/8” nc
X 1-3/4”
carriage bolts (#
9
) and
(4) 3/8” nc
self-locking nuts (#
12
).
Torque to 20 ft-lbs.
IMPORTANT :
Tighten in a manner not to permanently
deform the assembly.
6)
Repeat
steps 2
to
5
for the opposite side.
sketch D
LEFT
FRONT VIEW
Front of the ATV
