2810243
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
)
NT BUMPER
Kimpex
#
072915
aha Wolverine 1995
MOUNTING INSTRUCTIONS
ription
Item No.
Quantity
t bumper
81-828-1000
1
ort
81-828-2000
2
” nc X 3/4” hex bolt
S1711-00506-022 2
” nc X 2” hex bolt
S1711-00516-022 4
Ref. Description
Item No.
Quantity
�
5/16” nc self-locking nut
S4186-10500-022 6
�
1” dia X 4-1/4” “U” bracket
Q2116-20002
2
�
1” dia X 4-5/8” “U” bracket
Q2118-20001
2
�
Plastic cap
S8111-00007-500 2
o install a winch on a Kimpex front bumper, use the rear position holes, if not use the front holes.
the front bumper
�
under the lower tube of the wire netting.
(See sketch A)
er tube of the wire netting, fasten using
1-1/8” dia X 4-5/8”
“U” brackets
�
,
5/16” nc X 2”
hex bolts
�
, and
c
self-locking nuts
�
.
the lower part of the front bumper using the two supports
�
,
1” dia X 4-1/4”
“U” brackets
�
,
c X 2”
hex bolts
�
, and
5/16” nc
self-locking nuts
�
, on to the original frame.
(See sketch B)
the supports
�
under the bumper
�
using
5/16” nc X 3/4”
hex bolts
�
and
5/16” nc
self-locking nuts
�
.
in place.
(See sketch C)
the plastic caps
�
to the two ends of the tube.
(See sketch D)
C
sketch D
A
sketch B
A-2810243
ATV
Mounting instructions
front and REAR A-ARM BRACKET KIT
Kimpex
# 375717
For " Commander wide track " and " commander trek " track kits / yamaha grizzly 600, big bear 350
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
2810243
A-2810243
FRONT AND REAR A-ARM BRACKET KIT
Kimpex
#
375717
For “Commander Wide Track” and “Commander Trek” Track Kit
MOUNTING INSTRUCTIONS
9
sketch F
RIGHT
FRONT VIEW
WINCH PROTECTOR INSTALLATION
GRIZZLY 600 MODELS ONLY
(see sketch F)
1)
Fasten the rear part of the winch protector (#
7
) onto the rear
tube of the frame using the U-bracket (#
8
), a
5/16” nc X 1-3/4”
carriage bolt (#
11
), and a
5/16” nc
self-locking nut (#
16
) (screw
t e first threads only).
2)
Fasten the front part of the winch protector (#
7
) onto the front
tube of the frame using the
1-1/2” dia X 5-5/8”
U-bracket (#
9
), a
5/16” nc X 2-1/2”
carriage bolt (#
12
), a
5/16” dia
flat washer (#
19
),
and a
5/16” nc
self-locking nut (#
16
) (screw the first threads only).
3)
Make sure that the protector (#
7
) is aligned with the winch.
4)
Tighten all bolts. Torque to 13 ft-lbs.
MOUNT PLATE ASSEMBLING
(see sketch G)
WARNING :
Prior to installation, turn off the engine, put
in two-wheel driving mode, and block the wheels.
WARNING :
When the ATV is raised, make sure that it is
properly secured/supported to prevent it from
accidentally falling during the installation. If not properly
secured/supported, serious physical injury could occur.
1)
Fasten the
(2)
rear anti-rotation arm supports (#
4
) onto the
mount plate (#
10
) using the
(6) 3/8” nc X 1”
hex bolts (#
18
) and
the
(6) 3/8” nc
self-locking nuts (#
23
).
Front of the ATV
Winch
sketch G
