2810243
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
)
NT BUMPER
Kimpex
#
072915
aha Wolverine 1995
MOUNTING INSTRUCTIONS
ription
Item No.
Quantity
bumper
81-828-1000
1
ort
81-828-2000
2
” nc X 3/4” hex bolt
S1711-00506-022 2
” nc X 2” hex bolt
S1711-00516-022 4
Ref. Description
Item No.
Quantity
�
5/16” nc self-locking nut
S4186-10500-022 6
�
1” dia X 4-1/4” “U” bracket
Q2116-20002
2
�
1” dia X 4-5/8” “U” bracket
Q2118-20001
2
�
Plastic cap
S8111-00007-500 2
install a winch on a Kimpex front bumper, use the rear position holes, if not use the front holes.
the front bumper
�
under the lower tube of the wire netting.
(See sketch A)
er tube of the wire netting, fasten using
1-1/8” dia X 4-5/8”
“U” brackets
�
,
5/16” nc X 2”
hex bolts
�
, and
c
self-locking nuts
�
.
the lower part of the front bumper using the two supports
�
,
1” dia X 4-1/4”
“U” brackets
�
,
c X 2”
hex bolts
�
, and
5/16” nc
self-locking nuts
�
, on to the original frame.
(See sketch B)
the supports
�
under the bumper
�
using
5/16” nc X 3/4”
hex bolts
�
and
5/16” nc
self-locking nuts
�
.
in place.
(See sketch C)
the plastic caps
�
to the two ends of the tube.
(See sketch D)
sketch D
sketch B
A-2810243
ATV
Mounting instructions
front and REAR A-ARM BRACKET KIT
Kimpex
# 375717
For " Commander wide track " and " commander trek " track kits / yamaha grizzly 600, big bear 350
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
2810243
A-2810243
FRONT AND REAR A-ARM BRACKET KIT
Kimpex
#
375717
For “Commander Wide Track” and “Commander Trek” Track Kit
MOUNTING INSTRUCTIONS
12
“COMMANDER WIDE TRACK” /
REAR ANTI-ROTATION INSTALLATION
(see sketch M)
WARNING :
Prior to installation, turn off
the engine, put in two-wheel driving mode,
and block the wheels.
1)
Raise the rear of the ATV off the ground and
remove the wheels.
WARNING :
When the ATV is raised, make
sure that it is properly secured/supported to
prevent it from accidentally falling during
the installation. If not properly
secured/supported, serious physical injury
could occur.
2)
Screw the
5/8” nc
nut (#
21
) onto the threaded
part of the anti-rotation arm (#
8
).
3)
Install the
17mm I.D. X 50mm O.D. X 3mm
flat washer
(#
30
) and the bushing spacer tube (#
2
) onto the
threaded part of the anti-rotation arm (#
8
).
4)
Install the rubber bushing (#
1
) over the bushing
spacer tube (#
2
).
5)
Slide the anti-rotation arm assembly into the hole
of the rear right anti-rotation arm bracket (#
5
).
(see sketch N)
6)
Fasten the other end of the rear anti-rotation arm
(#
8
) onto the rear anti-rotation arm support (#
4
)
installed in
step 1 at the “MOUNT PLATE
ASSEMBLING”
using the
3/8” nc X 3”
hex bolt
(#
19
) and the
3/8” nc
nylock nut (#
23
).
(see sketch M)
7)
Install the rubber bushing (#
1
), the
3/4” I.D. X 2”
O.D. X 1/8”
flat washer (#
28
), and the other rubb r
bushing (#
1
) over the bushing spacer tube (#
2
).
8)
Install the
17mm I.D. X 50mm O.D. X 3mm
flat washer
(#
30
) onto the threaded part of the anti-rotation
arm (#
8
).
9)
Screw the
5/8” nc
self-locking nut (#
24
) onto the
threaded part of the anti-rotation arm (#
8
). Do
not overtighten.
NOTE :
Refer to the Track Kit manual for
the correct adjustment.
10)
Repeat
steps 2
to
9
for the opposite side.
sketch M
RIGHT
REAR VIEW
Rear of the ATV
sketch N
Rear of the ATV
