2810257
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
)
NT BUMPER
Kimpex
#
072915
aha Wolverine 1995
MOUNTING INSTRUCTIONS
ription
Item No.
Quantity
t bumper
81-828-1000
1
ort
81-828-2000
2
” nc X 3/4” hex bolt
S1711-00506-022 2
” nc X 2” hex bolt
S1711-00516-022 4
Ref. Description
Item No.
Quantity
�
5/16” nc self-locking nut
S4186-10500-022 6
�
1” dia X 4-1/4” “U” bracket
Q2116-20002
2
�
1” dia X 4-5/8” “U” bracket
Q2118-20001
2
�
Plastic cap
S8111-00007-500 2
o install a winch on a Kimpex front bumper, use the rear position holes, if not use the front holes.
the front bumper
�
under the lower tube of the wire netting.
(See sketch A)
er tube of the wire netting, fasten using
1-1/8” dia X 4-5/8”
“U” brackets
�
,
5/16” nc X 2”
hex bolts
�
, and
c
self-locking nuts
�
.
the lower part of the front bumper using the two supports
�
,
1” dia X 4-1/4”
“U” brackets
�
,
c X 2”
hex bolts
�
, and
5/16” nc
self-locking nuts
�
, on to the original frame.
(See sketch B)
the supports
�
under the bumper
�
using
5/16” nc X 3/4”
hex bolts
�
and
5/16” nc
self-locking nuts
�
.
in place.
(See sketch C)
the plastic caps
�
to the two ends of the tube.
(See sketch D)
C
sketch D
A
sketch B
A-2810257
ATV
Mounting instructions
front and REAR A-ARM BRACKET KIT
Kimpex
# 375612
For " Commander wide track " and " Commander trek " / suzuki king quad
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
2810257
A-2810257
FRONT AND REAR A-ARM BRACKET KIT
Kimpex
#
375612
For “Commander Wide Track” and “Commander Trek” Track Kit
MOUNTING INSTRUCTIONS
9
REAR A-ARM BRACKET INSTALLATION
(see sketch G)
WARNING :
Prior to installation, turn off the engine, put
in two-wheel driving mode, and block the wheels.
1)
Raise the rear of the ATV off the ground and remove the wheels.
WARNING :
When the ATV is raised, make sure that it is
properly secured/supported to prevent it from
accidentally falling during the installation of the A-arm
brackets. If not properly secured/supported, serious
physical injury could occur.
2)
Remove the rear left CV shield. Do not discard. They will be
reinstalled later.
3)
Assemble the rear tightening bended plate (#
14
) onto the rear
left A-arm bracket (#
1
) using the
3/8” nc X 1”
carriage bolt (#
16
)
and the
3/8” nc
self-locking nut (#
12
) (screw the first threads
only).
(see sketch H)
4)
Place the rear left A-arm bracket (#
1
) below the rear lower
A-arm. Install the
3/8” nc X 6”
hex bolt (#
15
) and the
3/8” nc
self-
locking nut (#
12
) above the rear lower A-arm (screw the first
threads only).
5)
Install the rear A-arm clamping plate (#
17
) and fasten using
(4)
3/8” nc X 2-1/4”
hex bolts (#
18
),
(6) 3/8” dia
flat washers (#
7
), and
(4)
3/8” nc
self-locking nuts (#
12
).
6)
Tighten all the bolts. Torque the
3/8” nc
nuts (#
12
) to 25 ft-lbs.
IMPORTANT :
Tighten in a manner not to permanently
deform the assembly.
7)
Repeat
steps 2
to
6
for the opposite side.
sketch G
LEFT
REAR VIEW
LEFT
REAR
VIEW
Rear of the ATV
Rear of
the ATV
sketch H
