2810257
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
)
NT BUMPER
Kimpex
#
072915
aha Wolverine 1995
MOUNTING INSTRUCTIONS
ription
Item No.
Quantity
bumper
81-828-1000
1
ort
81-828-2000
2
” nc X 3/4” hex bolt
S1711-00506-022 2
” nc X 2” hex bolt
S1711-00516-022 4
Ref. Description
Item No.
Quantity
�
5/16” nc self-locking nut
S4186-10500-022 6
�
1” dia X 4-1/4” “U” bracket
Q2116-20002
2
�
1” dia X 4-5/8” “U” bracket
Q2118-20001
2
�
Plastic cap
S8111-00007-500 2
install a winch on a Kimpex front bumper, use the rear position holes, if not use the front holes.
the front bumper
�
under the lower tube of the wire netting.
(See sketch A)
er tube of the wire netting, fasten using
1-1/8” dia X 4-5/8”
“U” brackets
�
,
5/16” nc X 2”
hex bolts
�
, and
c
self-locking nuts
�
.
the lower part of the front bumper using the two supports
�
,
1” dia X 4-1/4”
“U” brackets
�
,
c X 2”
hex bolts
�
, and
5/16” nc
self-locking nuts
�
, on to the original frame.
(See sketch B)
the supports
�
under the bumper
�
using
5/16” nc X 3/4”
hex bolts
�
and
5/16” nc
self-locking nuts
�
.
in place.
(See sketch C)
the plastic caps
�
to the two ends of the tube.
(See sketch D)
sketch D
sketch B
A-2810257
ATV
Mounting instructions
front and REAR A-ARM BRACKET KIT
Kimpex
# 375612
For " Commander wide track " and " Commander trek " / suzuki king quad
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
2810257
A-2810257
FRONT AND REAR A-ARM BRACKET KIT
Kimpex
#
375612
For “Commander Wide Track” and “Commander Trek” Track Kit
MOUNTING INSTRUCTIONS
8
FRONT ANTI-ROTATION INSTALLATION
(see sketch F)
NOTE :
Pay special attention to the orientation given to spacers (#5 and #6) during installation.
1)
Assemble the ball joint (#
18
) and the
1/2” nf
nut (#
17
) to the front anti-rotation assembly (#
13
)
.
2)
Install the large ball joint spacer (#
6
) with the narrow part facing down onto the
1/2” nc X 2-1/2”
carriage bolt (#
11
) installed in
step 3 of
the “FRONT A-ARM BRACKET INSTALLATION” section.
3)
Install the ball joint of the front anti-rotation assembly (#
13
) onto the bolt (#
11
), below the large ball joint spacer (#
6
). Install the short
ball joint spacer (#
5
) with the narrow part facing up, below the anti-rotation assembly (#
13
).
4)
Tighten the assembly with the
1/2” nc
self-locking nut (#
10
). Torque to 55 ft-lbs.
WARNING :
If the bolts ar not ufficiently ightened, there is a risk of them becoming loose, of parts detaching and risk
of loss of control over the vehicle, as well as risk of personal injury.
5)
Rotate the anti-rotation assembly (#
13
) towards the center of the ATV to prevent it from interfering with the in tallation of the Track Kit.
NOTE :
Refer to the Track Kit manual for the correct adjustment (section 3, page 17).
6)
Repeat
steps 1
to
5
for the opposite side.
sketch F
LEFT
FRONT VIEW
Front of the ATV
