2810262
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
)
NT BUMPER
Kimpex
#
072915
aha Wolverine 1995
MOUNTING INSTRUCTIONS
ription
Item No.
Quantity
bumper
81-828-1000
1
ort
81-828-2000
2
” nc X 3/4” hex bolt
S1711-00506-022 2
” nc X 2” hex bolt
S1711-00516-022 4
Ref. Description
Item No.
Quantity
�
5/16” nc self-locking nut
S4186-10500-022 6
�
1” dia X 4-1/4” “U” bracket
Q2116-20002
2
�
1” dia X 4-5/8” “U” bracket
Q2118-20001
2
�
Plastic cap
S8111-00007-500 2
install a winch on a Kimpex front bumper, use the rear position holes, if not use the front holes.
the front bumper
�
under the lower tube of the wire netting.
(See sketch A)
er tube of the wire netting, fasten using
1-1/8” dia X 4-5/8”
“U” brackets
�
,
5/16” nc X 2”
hex bolts
�
, and
c
self-locking nuts
�
.
the lower part of the front bumper using the two supports
�
,
1” dia X 4-1/4”
“U” brackets
�
,
c X 2”
hex bolts
�
, and
5/16” nc
self-locking nuts
�
, on to the original frame.
(See sketch B)
the supports
�
under the bumper
�
using
5/16” nc X 3/4”
hex bolts
�
and
5/16” nc
self-locking nuts
�
.
in place.
(See sketch C)
the plastic caps
�
to the two ends of the tube.
(See sketch D)
sketch D
sketch B
A-2810262 Rév. A
ATV
Mounting instructions
front and REAR A-ARM BRACKET KIT
Kimpex
# 375616
For " Commander wide track " and " commander trek " track kits / suzuki vinson 500
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
2810262
A-2810262 Rév. A
FRONT AND REAR A-ARM BRACKET KIT
Kimpex
#
375616
For “Commander Wide Track” and “Commander Trek” Track Kit
MOUNTING INSTRUCTIONS
8
SNOWPLOW ADAPTER INSTALLATION
(see sketch F)
WARNING :
Prior to installation, turn off the engine, put in two-wheel
driving mode, and block the wheels.
WARNING :
When the ATV is raised, make sure that it is properly
secured/supported to prevent it from accidentally falling during the
installation. If not properly secured/supported, serious physical injury
could occur.
1)
Fasten the
(2)
rear anti-rotation arm supports (#
4
) onto the snowplow adapter
(#
20
) using
(6) 3/8” nc X 1”
hex bolts (#
10
) and
(6) 3/8” nc
self-locking nuts (#
15
).
NOTE :
Refer to the snowplow adapter mounting instructions (no.
073627) to finish the installatio .
• TO FINISH THE INSTALLATION OF “COMMANDER WIDE TRACK”
MODELS, SEE PAGES 8 TO 10.
• TO FINISH THE INSTALLATION OF “COMMANDER TREK” MODELS,
SEE PAGES 11 AND 12.
“COMMANDER WIDE TRACK” / REAR ANTI-ROTATION ARM BRACKET INSTALLATION
(see sketch G)
1)
Unscrew the self-locking nut (#
A
) from the 1/2” nc X 6” hex bolt (#
B
) retaining the wheel closer to the adjustment slide (#
C
). Remove
and discard the flat washer (#
D
).
(see sketch H)
2)
Assemble the rear right anti-rotation arm bracket (#
6
) to the hole made for this purpose in the plastic frame of the Track Kit using
(3) 3/8” nc X 3-1/2”
hex bolts (#
12
), a
3/8” I.D. X 1-1/4” O.D. X .120”
Fender washer (#
19
), the rear anti-rotation arm clamping plate (#
8
),
(3) 3/8”
nc self-locking nuts (#
15
), and the original self-locking nut (#
A
) removed in
step 1
.
3)
Repeat
steps 1
and
2
for the opposite side.
sketch F
sketch G
RIGHT
REAR VIEW
Rear of
the ATV
sketch H
