2810262
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
)
NT BUMPER
Kimpex
#
072915
aha Wolverine 1995
MOUNTING INSTRUCTIONS
ription
Item No.
Quantity
bumper
81-828-1000
1
ort
81-828-2000
2
” nc X 3/4” hex bolt
S1711-00506-022 2
” nc X 2” hex bolt
S1711-00516-022 4
Ref. Description
Item No.
Quantity
�
5/16” nc self-locking nut
S4186-10500-022 6
�
1” dia X 4-1/4” “U” bracket
Q2116-20002
2
�
1” dia X 4-5/8” “U” bracket
Q2118-20001
2
�
Plastic cap
S8111-00007-500 2
install a winch on a Kimpex front bumper, use the rear position holes, if not use the front holes.
the front bumper
�
under the lower tube of the wire netting.
(See sketch A)
er tube of the wire netting, fasten using
1-1/8” dia X 4-5/8”
“U” brackets
�
,
5/16” nc X 2”
hex bolts
�
, and
c
self-locking nuts
�
.
the lower part of the front bumper using the two supports
�
,
1” dia X 4-1/4”
“U” brackets
�
,
c X 2”
hex bolts
�
, and
5/16” nc
self-locking nuts
�
, on to the original frame.
(See sketch B)
the supports
�
under the bumper
�
using
5/16” nc X 3/4”
hex bolts
�
and
5/16” nc
self-locking nuts
�
.
in place.
(See sketch C)
the plastic caps
�
to the two ends of the tube.
(See sketch D)
sketch D
sketch B
A-2810262 Rév. A
ATV
Mounting instructions
front and REAR A-ARM BRACKET KIT
Kimpex
# 375616
For " Commander wide track " and " commander trek " track kits / suzuki vinson 500
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
2810262
A-2810262 Rév. A
FRONT AND REAR A-ARM BRACKET KIT
Kimpex
#
375616
For “Commander Wide Track” and “Commander Trek” Track Kit
MOUNTING INSTRUCTIONS
6
FRONT A-ARM BRACKET INSTALLATION
(see sketch D)
WARNING :
Prior to installation, turn off the engine, put
in two-wheel driving mode, and block the wheels.
1)
Raise the front of the ATV off the ground and remove the
wheels.
WARNING :
When the ATV is raised, make sure that it is
properly secured/supported to prevent it from
accidentally falling during the installation of the A-arm
brackets. If not properly secured/supported, serious
physical injury could occur.
2)
Remove the front left CV shield. Do not discard. They will be
reinstalled later.
3)
Insert the
1/2” nc X 2-1/2”
carriage bolt (#
9
) into the hole intended
in the front left A-arm bracket (#
5
).
4)
Install the front left A-arm bracket (#
5
) under the lower front
A-arm so that the two parts fit snugly.
5)
Install the front A-arm clamping plate (#
6
) above the lower front
A-arm and fasten it to the A-arm bracket (#
5
) using the
(3)
3/8” nc X 2”
hex bolts (#
7
) and the
(3) 3/8” nc
self-locking nuts (#
10
).
Torque to 20 ft-lbs.
IMPORTANT :
Tighten in a manner not to permanently
deform the assembly.
6)
Repeat
steps 2
to
5
for the opposite side.
sketch D
LEFT
FRONT VIEW
Front of
the ATV
