2810351
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
)
NT BUMPER
Kimpex
#
072915
aha Wolverine 1995
MOUNTING INSTRUCTIONS
ription
Item No.
Quantity
t bumper
81-828-1000
1
ort
81-828-2000
2
” nc X 3/4” hex bolt
S1711-00506-022 2
” nc X 2” hex bolt
S1711-00516-022 4
Ref. Description
Item No.
Quantity
�
5/16” nc self-locking nut
S4186-10500-022 6
�
1” dia X 4-1/4” “U” bracket
Q2116-20002
2
�
1” dia X 4-5/8” “U” bracket
Q2118-20001
2
�
Plastic cap
S8111-00007-500 2
o install a winch on a Kimpex front bumper, use the rear position holes, if not use the front holes.
the front bumper
�
under the lower tube of the wire netting.
(See sketch A)
er tube of the wire netting, fasten using
1-1/8” dia X 4-5/8”
“U” brackets
�
,
5/16” nc X 2”
hex bolts
�
, and
c
self-locking nuts
�
.
the lower part of the front bumper using the two supports
�
,
1” dia X 4-1/4”
“U” brackets
�
,
c X 2”
hex bolts
�
, and
5/16” nc
self-locking nuts
�
, on to the original frame.
(See sketch B)
the supports
�
under the bumper
�
using
5/16” nc X 3/4”
hex bolts
�
and
5/16” nc
self-locking nuts
�
.
in place.
(See sketch C)
the plastic caps
�
to the two ends of the tube.
(See sketch D)
C
sketch D
A
sketch B
A-281351
ATV
Mounting instructions
front and REAR A-ARM BRACKET KIT
Kimpex
# 375713
For " Commander wide track " and " commander trek " track kits / yamaha kodiak 400, 450 (ind. susp.)
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
2810351
A-2810351
FRONT AND REAR A-ARM BRACKET KIT
Kimpex
#
375713
For “Commander Wide Track” and “Commander Trek” Track Kit
MOUNTING INSTRUCTIONS
9
Rear of the ATV
REAR A-ARM BRACKET INSTALLATION
(see sketch I)
WARNING :
Prior to installation, turn off the engine, put in two-wheel driving mode and the transmission in neutral,
and block the wheels.
1)
Raise the rear of the ATV off the ground and remove the wheels.
WARNING :
When the ATV is raised, make sure that it is properly secured/supported to prevent it from accidentally
falling during the installation of the sub-tables. If not properly secured/supported, serious physical injury could occur.
2)
Remove the rear left CV shield. Do not discard. They will be reinstalled later.
3)
Ins all the rear left A-arm bracket (#
6
) under the lower front A-arm so that the two parts fit snugly.
4)
Install the rear A-arm clamping plate (#
5
) above the lower rear A-arm and fasten it to the A-arm bracket (#
6
) using the
(4) 3/8” nc X 2-1/4”
carriage bolts (#
9
) and the
(4) 3/8” nc
self-locking nuts (#
11
). Torque to 20 ft-lbs.
IMPORTANT :
Tighten in a manner not to permanently deform the assembly.
5)
Rep a
steps 2
to
4
for the opposite side.
sketch I
LEFT
REAR VIEW
