2810299
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
)
NT BUMPER
Kimpex
#
072915
aha Wolverine 1995
MOUNTING INSTRUCTIONS
ription
Item No.
Quantity
bumper
81-828-1000
1
ort
81-828-2000
2
” nc X 3/4” hex bolt
S1711-00506-022 2
” nc X 2” hex bolt
S1711-00516-022 4
Ref. Description
Item No.
Quantity
�
5/16” nc self-locking nut
S4186-10500-022 6
�
1” dia X 4-1/4” “U” bracket
Q2116-20002
2
�
1” dia X 4-5/8” “U” bracket
Q2118-20001
2
�
Plastic cap
S8111-00007-500 2
install a winch on a Kimpex front bumper, use the rear position holes, if not use the front holes.
the front bumper
�
under the lower tube of the wire netting.
(See sketch A)
er tube of the wire netting, fasten using
1-1/8” dia X 4-5/8”
“U” brackets
�
,
5/16” nc X 2”
hex bolts
�
, and
c
self-locking nuts
�
.
the lower part of the front bumper using the two supports
�
,
1” dia X 4-1/4”
“U” brackets
�
,
c X 2”
hex bolts
�
, and
5/16” nc
self-locking nuts
�
, on to the original frame.
(See sketch B)
the supports
�
under the bumper
�
using
5/16” nc X 3/4”
hex bolts
�
and
5/16” nc
self-locking nuts
�
.
in place.
(See sketch C)
the plastic caps
�
to the two ends of the tube.
(See sketch D)
sketch D
sketch B
A-2810299
ATV
Mounting instructions
front and REAR A-ARM BRACKET KIT
Kimpex
# 375222
For " Commander wide track " and " Commander trek " / Honda trx 420 2009
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
2810299
A-2810299
FRONT AND REAR A-ARM BRACKET KIT
Kimpex
#
375222
For “Commander Wide Track” and “Commander Trek» Track Kit
MOUNTING INSTRUCTIONS
8
REAR A-ARM BRACKET INSTALLATION
WARNING :
Prior to installation, turn off the engine, put
in two-wheel driving mode, and block the wheels.
1)
Raise the rear of the ATV off the ground and remove the wheels.
WARNING :
When the ATV is raised, make sure that it is
properly secured/supported to prevent it from
accidentally falling during the installation of the A-arm
brackets. If not properly secured/supported, serious
physical injury could occur.
(see sketch G)
2)
Remove the existi g bolts (#
A
a d #
C
) and nuts (#
B
and #
D
) as
illustrated.
(see sketch H)
3)
Positi n the rear left A-arm bracket (#
5
) below the lower rear
A-arm so that the two parts fit snugly.
4)
Fasten the exterior part of the rear left A-arm bracket (#
5
) onto
A-arm using the
M10-1.5 X 110mm
hex bolt (#
6
) and the
M10-1.5
self-
locking nut (#
13
). Torque to 20 ft-lbs.
5)
Fasten the interior part of the rear left A-arm bracket (#
5
) onto
A-arm using the
M14-2.0 X 150mm
hex bolt (#
7
) and the
M14-2.0
self-
locking nut (#
14
). Torque to 63 ft-lbs.
IMPORTANT :
Tighten in a manner not to permanently
deform the assembly.
6)
Repeat
steps 2
to
5
for the opposite side.
sketch G
LEFT
REAR VIEW
Front of the ATV
Front of the ATV
sketch H
LEFT
REAR VIEW
