2810328
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
)
NT BUMPER
Kimpex
#
072915
aha Wolverine 1995
MOUNTING INSTRUCTIONS
ription
Item No.
Quantity
t bumper
81-828-1000
1
ort
81-828-2000
2
” nc X 3/4” hex bolt
S1711-00506-022 2
” nc X 2” hex bolt
S1711-00516-022 4
Ref. Description
Item No.
Quantity
�
5/16” nc self-locking nut
S4186-10500-022 6
�
1” dia X 4-1/4” “U” bracket
Q2116-20002
2
�
1” dia X 4-5/8” “U” bracket
Q2118-20001
2
�
Plastic cap
S8111-00007-500 2
o install a winch on a Kimpex front bumper, use the rear position holes, if not use the front holes.
the front bumper
�
under the lower tube of the wire netting.
(See sketch A)
er tube of the wire netting, fasten using
1-1/8” dia X 4-5/8”
“U” brackets
�
,
5/16” nc X 2”
hex bolts
�
, and
c
self-locking nuts
�
.
the lower part of the front bumper using the two supports
�
,
1” dia X 4-1/4”
“U” brackets
�
,
c X 2”
hex bolts
�
, and
5/16” nc
self-locking nuts
�
, on to the original frame.
(See sketch B)
the supports
�
under the bumper
�
using
5/16” nc X 3/4”
hex bolts
�
and
5/16” nc
self-locking nuts
�
.
in place.
(See sketch C)
the plastic caps
�
to the two ends of the tube.
(See sketch D)
C
sketch D
A
sketch B
A-2810328 Rév. A
ATV
Mounting instructions
front and REAR A-ARM BRACKET KIT
Kimpex
# 375219
For " Commander wide track " and " Commander trek " / HONDA trx 350 1986-1993
KIMPEX INC.
/ 5355, rue St-Roch / Drummondville (Québec) Canada / J2B 6V4
KIMPEX USA
/ 100 Walnut Street / Champlain, New York / 12919
Lithographié au Canada / Litho’d in Canada
2810328
A-2810328 Rév. A
FRONT AND REAR A-ARM BRACKET KIT
Kimpex
#
375219
For “Commander Wide Track” and “Commander Trek” Track Kit
MOUNTING INSTRUCTIONS
7
“COMMANDER TREK” /
FRONT ANTI-ROTATION BRACKET INSTALLATION
(see sketch H)
1)
Unscrew the self-locking nut (#
A
) from the M10 bolt (#
B
)
retaining the wheel closer to the adjustment slide. Keep the self-
locking nut (#
A
).
(see sketch I)
2)
Insert a
3/8” nc X 1-1/2”
carriage bolt (#
13
) into the hole made for
this purpose in the front antirotation bracket (#
5
) as illustrated.
3)
Fasten the upper part of the front antirotation bracket (#
5
) onto
the frame of the Track Kit sing a
3/8” nc X 3-1/2”
h x bolt (#
10
) and
a
3/8” nc
self-locking nut (#
15
).
Fasten the lower part of the front antirotation bracket (#
5
) onto
the frame of the Track Kit using a
M10-1.5 X 90mm
hex bolt (#
9
), the
spacer (#
7
), and the self-locking nut (#
A
) removed in
step 1
.
4)
Repeat
steps 1
to
3
for the opposite side.
“COMMANDER TREK” /
FRONT ANTI-ROTATION INSTALLATION
(see sketch J)
WARNING :
Prior to installation, turn off the engine, put
in two-wheel driving mode and the transmission in
neutral, and block the wheels.
WARNING :
When the ATV is raised, make sure that it is
properly secured/supported to prevent it from
accidentally falling during the installation. If not properly
secured/supported, serious physical injury could occur.
1)
Fasten the front anti-rotation assembly (#
4
) onto the front anti-
rotation bracket (#
5
) using the
3/8” nc X 1-1/2”
carriage bolt (#
13
),
the tightening spacer (#
3
), the
3/8” dia
flat washer (#
16
), and the
3/8” nc
self-locking nut (#
15
).
NOTE :
Refer to the Track Kit manual for the correct
adjustment.
2)
Repeat
step 1
for the opposite side.
sketch H
sketch J
sketch I
LEFT FRONT VIEW
LEFT FRONT VIEW
Front of
the ATV
Front of
the ATV
LEFT FRONT VIEW
Front of
the ATV
